If you notice water dripping from the bottom of your tank or sitting in a rusty pool beneath it, this means that the steel tank has rusted through. This kind of damage is not fixable and the tank will need to be replaced. However, if you are experiencing problems such as insufficient or no hot water, your heater may just need to be fixed rather than replaced. If you’re unsure what the problem is, call a professional plumber.
It is also a good idea to provide a description of the new water heater and the materials you intend to use while installing it. The plumbing inspector may have some useful feedback or advice that will help you with your installation. If this is your first time replacing a water heater and you are concerned with safety, you can request for a local plumbing or electrical inspector to check your work.
Tools: screwdriver, adjustable wrench, pipe wrench, tube cutter, wire stripper/cutter electrical tape, plumbers tape, carpenter’s level, tape measure, rags and safety glasses. Materials: new gas (or electric) water heater, water and gas piping, fittings, solder, pressure relief valve, discharge pipe, pipe thread compound, venting pipe and connectors.
When the gas is off, the valve handle should be at a right angle to the pipe. Check the pilot light to make sure it’s out. Smell for the presence of gas before proceeding. If you’re replacing an electric heater, remove the fuse or turn off the circuit breaker to cut off power to the water heater. [1] X Research source
Start draining the tank by opening a hot water faucet on the lowest floor of the house. This will make the tank lighter and easier to move. Connect a hose to the drain valve on the tank and slowly open the valve. Allow the water to run off into a nearby drain or bucket. Be very careful, as the water may be scalding hot. Once the water flow starts to decrease, you’ll know that you’re nearly done.
Use two pipe wrenches to disconnect the gas line at the union or flare fitting. Then use a pipe wrench to unscrew the pipe from the gas control valve. If you have an electric water heater, simply disconnect the electrical service. Disconnect the hot and cold water lines. If the pipes have been soldered into place, you will need to cut them using a tubing cutter or a hacksaw. Try to ensure that the cuts are as straight as possible. [2] X Research source Detach the vent from the water heater by removing the screws which connect the two. Push the vent pipe to one side.
You may need some help doing this as older water heaters are often filled with sediment, making them very heavy. If your water heater is in the basement, consider renting an appliance dolly to help you bring the new heater down and the old heater up. Dispose of the old water heater safely and legally. Contact a local waste management department or sanitation agency for instructions on how to recycle a water heater. Most states have current laws prohibiting the dumping of appliances such as water heaters in dumps or landfills.
Twist the heater around so that the plumbing locations are lined up with the appropriate pipes. Use a carpenter’s level to ensure that the heater is sitting straight. Use some wooden shims to adjust the level if necessary.
Solder the adapters to the pipes at a work surface away from the water heater, as you don’t want to place a heat source too close to the tank. Attach the adapters to the hot water output and cold water input at the top of the tank using pipe joint compound or Teflon tape. Some local plumbing codes will also require you to attach plastic lined nipples to the bottom of each pipe assembly. This prevents galvanic corrosion, something which is particular important in hard water areas.
Solder the two edges of pipe together, using copper slip couplings or dielectric unions (to prevent electrolysis). If you can’t get the old and new pipes to align properly, connect them using pieces of flexible copper pipes or 45 degree elbows.
Use two pipe wrenches to screw the first nipple into the gas valve, then continue to reassemble the remaining fittings. The last connection should be the union fitting, as this connects the new line to the old. Once this is connected, you can turn on the gas supply valve. To connect electric heaters to their power supply, reconnect the power lines and ground wire to the junction box.
If there’s a leak, soap bubbles will form on the surface of the sponge. If this happens, you will need to tighten or reconnect the joints, or a call a professional plumber. If there are no bubbles, the joints are secure and you are free to turn on the water and power supply.
If your water heater is electric, turn the power on by reinstalling the fuse or resetting the circuit breaker in the power panel. [4] X Research source
